How to Build a Fishing Chair
Sure, you can go to the big department store and
buy an aluminum and polyester cloth chair for less than 20 bucks, but this chair
can be built from scratch with scrap lumber in less time, and you can be on your
way to
that favorite fishing hole. Here's how it's done.
buy an aluminum and polyester cloth chair for less than 20 bucks, but this chair
can be built from scratch with scrap lumber in less time, and you can be on your
way to
that favorite fishing hole. Here's how it's done.
Step 1
Gather the tools and materials you will need. Keep it simple! A
circular saw, drill with a screw-driving attachment, and an extension cord are
all the power equipment used for the chair in these photos. Along with the
tools, some 2 inch wood screws, scrap cedar 1X2s from a construction dumpster, a
treated 2X4 8 foot long, and a tape and square were all that were used for this
project.
circular saw, drill with a screw-driving attachment, and an extension cord are
all the power equipment used for the chair in these photos. Along with the
tools, some 2 inch wood screws, scrap cedar 1X2s from a construction dumpster, a
treated 2X4 8 foot long, and a tape and square were all that were used for this
project.
Step 2
Rip some 2x4 lumber 1 1/2 inches wide, various lengths. For
reference, the actual angles and cut lengths for this chair are listed under
Things You'll Need. Note that these can be modified to fit the
individual's preferences.
reference, the actual angles and cut lengths for this chair are listed under
Things You'll Need. Note that these can be modified to fit the
individual's preferences.
Step 3
Find a flat surface to lay out your pieces. The photo will
illustrate this step better than it can be described, but basically, you have
the seat support intersecting with the back frame at about a 53 degree angle.
Next, a rear leg support intersects with the seat, about 8 to 10 inches from the
back frame
illustrate this step better than it can be described, but basically, you have
the seat support intersecting with the back frame at about a 53 degree angle.
Next, a rear leg support intersects with the seat, about 8 to 10 inches from the
back frame
Step 4
Align the back and seat frame members so the angle suits you, then place
the back leg member underneath in a position that will allow you to scribe it to
cut to length after you have fit the rest of the frame together
the back leg member underneath in a position that will allow you to scribe it to
cut to length after you have fit the rest of the frame together
Step 5
Mark each framing member where it intersects the adjacent one.
This will give you the angle of each cut, and because the seat and back angle
are subject to personal preference, we won't go into great detail here.
This will give you the angle of each cut, and because the seat and back angle
are subject to personal preference, we won't go into great detail here.
Step 6
Cut the marks you have scribed with your circular saw, and dry fit the
pieces together. You may want to tack them with a wood screw to get an
idea if the finished chair will sit at the right height and angle for you.
pieces together. You may want to tack them with a wood screw to get an
idea if the finished chair will sit at the right height and angle for you.
Step 7
Attach the frame in the configuration illustrated in the photo, using 2
inch, number 12 wood screws. Countersink them if you prefer, but keep
in mind, these steps describe building a fishing chair, not a showroom piece of
furniture.
inch, number 12 wood screws. Countersink them if you prefer, but keep
in mind, these steps describe building a fishing chair, not a showroom piece of
furniture.
Step 8
Attach the front leg, fastening it through the joint of the rear leg and
seat support to give this connection increased strength
seat support to give this connection increased strength
Step 9
Stand the chair up on your work surface, and tilt it so that it is at
the correct height and amount of reclining angle you want, then scribe either
the front, rear, or both legs to cut them to length. If you make a
mistake here, you can always unscrew the miscut piece and replace it, but cut
long, it is easier to lower the chair seating height than to raise it.
the correct height and amount of reclining angle you want, then scribe either
the front, rear, or both legs to cut them to length. If you make a
mistake here, you can always unscrew the miscut piece and replace it, but cut
long, it is easier to lower the chair seating height than to raise it.
Step 10
Cut strips of wood 1 1/2 inches wide, and 3/4 inch thick, about 20
inches long. These are your seat slats, and you can cut longer slats
for wider seats, or reduce the length for narrow fisherpersons
inches long. These are your seat slats, and you can cut longer slats
for wider seats, or reduce the length for narrow fisherpersons
Step 11
Attach three of the slats, one at the point where the back intersects
the seat, one at the front of the seat, and one at the top of the back, as shown
in the photo. Use one screw in each end so you can rack the
assembly if it is out of square.
the seat, one at the front of the seat, and one at the top of the back, as shown
in the photo. Use one screw in each end so you can rack the
assembly if it is out of square.
Step 12
Square up your chair frame. If you prefer, you can eye-ball the
assembly, but using a steel square will insure the finished chair doesn't wobble
when it is set on a flat surface.
assembly, but using a steel square will insure the finished chair doesn't wobble
when it is set on a flat surface.
Step 13
Finish attaching the slats for the seat and back of your chair.
Depending on how deep the seat is, and how high the back is, you will
need a total of about 20 slats. These can be spaced half an inch or so apart so
water will drain through them if left in the rain.
Depending on how deep the seat is, and how high the back is, you will
need a total of about 20 slats. These can be spaced half an inch or so apart so
water will drain through them if left in the rain.
Step 14
Rip 1/2 inch thick strips of 1 1/2 inch wide lumber to attach to the
back frame as a cross bracing to make the chair stable. Attach these
strips as shown in the photo, after making sure the frame is square.
back frame as a cross bracing to make the chair stable. Attach these
strips as shown in the photo, after making sure the frame is square.
Step 15
Cut the armrests, again, as shown in the photo. Here, since
there was no thinner lumber laying around, a 2X4 was split width-wise to yield
two 1X4s, about 19 inches long
there was no thinner lumber laying around, a 2X4 was split width-wise to yield
two 1X4s, about 19 inches long
Step 16
Attach your armrests to the top of the front leg posts, and to the back
frame. This attachment should be very secure, since it reinforces the
back frame and stabilizes the chair assembly.
frame. This attachment should be very secure, since it reinforces the
back frame and stabilizes the chair assembly.
Step 17
Finish the chair if you like, but for all practical purposes, you are
ready to go fishing
ready to go fishing